Download: MiCOM P44x Order Form Cortec Configurator P P P P P P – Easergy MiCOM P44x. Alstom Generator Protection relay Micom P (Numerical relay),Alstom- Transmission-P,MiCOM Agile P, P & P (Distance Protection Systems). MiCOM P, P and P Numerical Full Scheme Distance Relays . range of protection functions listed in the table, the P, P and.
|Published (Last):||8 July 2005|
|PDF File Size:||20.14 Mb|
|ePub File Size:||10.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
The levels of access are summarised in Table 2. Alstom Grid Automation provides utilities and industry with the mission critical software systems and equipment needed to manage the flow of electricity in transmission and distribution grids, ensure grid stability and to protect and control substations.
MiCOM P44x Order Form Cortec Configurator P441 P442 P443 P444 P445 P446
The standard defines and offers much more than just a protocol. This reduces the amount of processing time that is used by the PSL. As this affects the operation of each of the individual protection functions, it is described in the following section. All current and voltage signals, digital logic input signals and output contacts are connected at the rear of the relay.
It must also be ensured that the relay is set above any standing level of p42 voltage aletom is present on the healthy system. MiCOM provides the p4422 to define an application solution and, through extensive communication capabilities, to integrate it with your power supply control system.
The technical data in this Safety Section is typical only, see the technical data section of the relevant equipment documentation for data specific to a particular equipment.
The third and fourth overcurrent stages can be set as follows: Hence, in practice, it would be associated with a long time delay. The angle that occurs between V2 and I2 under fault conditions is directly dependent upon the negative sequence source impedance of the system. Technical Guide, includes information on the application of the akstom and a technical description of its features.
This is achieved by the use of an additional opto-board which contains the same provision for 8 isolated digital inputs as the main input board, but does not contain alxtom of the circuits for analogue signals which are provided on the main input board.
It is not possible to go straight to the default display from within one of the column cells using the auto-repeat facility of the key, as the auto-repeat will stop at the column heading.
Otherwise the locus of the 3 single phase loops have passed through the polygon indicating loss of synchronism and the sign of R is different from the point of entry ; then an out of step is detected.
It must be noted however, that lastom ratio may vary depending upon the fault location. Thus the negative sequence current threshold is: However, as with the maximum number of gates, the practical limit is determined by the complexity of the logic. Undervoltage Protection – Two stage, configurable as either phase to phase or phase to neutral measuring. Alternatively, the logic can be chosen to be enabled when the channel associated with an aided scheme has alstpm.
For this reason only qualified personnel may work on or l442 the equipment. This Safety Section also includes reference to typical equipment label markings. Time Synch Enabled The time synch can be lastom to either enabled or disabled. With the cover in place read only access to the user interface is possible. It is only possible to move across columns at the column heading level. In practice, this minimum setting is governed by the levels of standing negative phase sequence lastom present on the system.
A relay may have up to internal signals each reference by a numeric index as shown in this table. To return to the default display press the key or the clear key from any of the column headings. PSB is indicated on reaching zone 3 or zone 4. It should be noted that, the setting values will also be discarded if the menu time out occurs before the setting changes have been confirmed. When electrical equipment is in operation, dangerous voltages will be present in certain parts of the equipment.
This provides good earthing at all joints giving a low impedance path p42 earth which is essential for performance in the presence of external noise. An underfrequency condition at nominal voltage can result in over-fluxing of generators and transformers and many types of industrial loads have limited tolerances on the operating frequency and running speeds e.
F menu The option of using separate channels for DEF aided tripping, and distance protection schemes, is offered in the P, P and P relays. The three options are shown in table 1 below.
Agile P, P and P distance protection – Specifications
The generic substation event model provides the possibility for a fast and reliable system-wide distribution of input and output data values. They offer complete, cost-effective and highly reliable protection for operating machines. The settings for this port are located immediately below the ones for the first port as described in previous sections of this chapter. Any device that is interested in the information subscribes i. Factory default settings associate specific relay functions with these 10 direct-action pushbuttons and LEDs e.
This, coupled with operation alsstom a Zone 2 comparator causes tripping of the local circuit breaker. Standard and ;442 signalling schemes are available to give fast fault clearance for the whole of the protected line or cable. It is important that no two relays have the same DNP 3. This can be determined from a system study, or by making use of the relay measurement facilities at the commissioning stage.
The disturbance recorder is supplied with data by the protection and control task once per cycle. It also processes the distance algorithms. If the fault is in the forward direction, then S i 0.
With Kbus or ModBus comms, the relay attempts to limit the demands on memory space by saving the analogue data in compressed format whenever possible.