2N Central Semiconductor Bipolar Transistors – BJT PNP Ampl/Switch datasheet, inventory, & pricing. Data Sheet No. 2N Generic Part Number: 2N REF: MIL-PRF/ Features: • General-purpose transistor for high speed switching and driver. 2N And 2N ARE PNP SMALL SIGNAL GENERAL PURPOSE NJ Semi-Conductors encourages customers to verify that datasheets are current.

Author: Megore Vudokasa
Country: Thailand
Language: English (Spanish)
Genre: Automotive
Published (Last): 17 August 2016
Pages: 311
PDF File Size: 13.70 Mb
ePub File Size: 5.54 Mb
ISBN: 386-7-64365-955-9
Downloads: 77655
Price: Free* [*Free Regsitration Required]
Uploader: Vozil

I kind of suspect a diode, but can’t figure out why a plain old diode wouldn’t work better and be a lot cheaper. A transistor connected like this acts as a diode with SUPER fast on and off times, as well as super low forward resistance.

I can’t speak for datasheeh real world configuration as I haven’t actually used a transistor like this but it did almost what I thought it would. Sign up using Email and Password. Both transistors here are PNP. Why do you say datasheeg RobhercKV5ROB This is odd, because this is exactly how BJT switches work; they are deeply saturated, with the base current way higher than minimal current required for the required collector current.

Still guessing, but to me shorting C-E together in that installation may be for protecting the transistor from damage if a ‘floating lead’ picks ul a harmful voltage, or damage that purportedly can be caused by running a transistkr with too much base current vs collector-emitter current I remember back in my early EE days reading textbooks warning of premature death from oversignalling transistors without enough avail.

Post as a guest Name. I renamed the transistors to reflect Op’s circuit, to avoid confusion.


Would that be likely to have the same voltage drop but allow more current or something? But the accuracy of the scaling is controlled by the V BE match. Mouser Electronics ha disabilitato il TLS 1. Sign up using Facebook.

Redrawing clarifies simple circuits. Voltage divides and current flows top-to-bottom. Test your settings by visiting www.

Of course, given that the application note suggests a diode, that’s probably not the case. The scaling factor is decided by the ratio of the two emitter resistors. For the best V BE match, the transistors should be the same type, and their temperatures should be kept close, by mounting them on the same heat sink even though Q1 has very little dissipation.

Putting the plain diode on the heat sink with the transistor might be an improvement. Email Required, but never shown. Ricardo 4, 14 37 What would be the rationale for using the C-B junction as well dstasheet the E-B junction?

I have never used them in the configuration of the question schematic. What role would Q2 play in that configuration? Or possibly it’s just to datassheet up loose ends’ and not leave datasheef floating lead. The regulator also sends some current to ground.

Can you see the picture I uploaded as I can not? Their LM data sheet has the second layout.

Buy 2N PNP General Purpose Transistor | Robomart India

Some suggested transistors are listed below. This short circuit protection is added because of the use of an external pass transistor prevents the internal short circuit protection from working. How to Derate ; Guideline for Derating Components. First these curves relate to sea level, just as 2n datasheet datasheet numbers 2n datasheet provided at 25 degrees Centigrade.


In this configuration they almost have the same IV curve, but the NPN doesn’t work the same as a diode when in the negative sweep like two back to back diodes would. Who knew you could build a switching converter datashfet an LM? This current boost circuit takes advantage of the internal current limiting characteristics of the regulator to provide short-circuit current protection for the booster as well. I do not know who 2n datasheet the transistor but close datasueet will 2n likely 2n datasheet dataheet.

Number things left-to-right and top-to-bottom. Datawheet the base resistor value should be 5V — 0. Have you datasjeet citations or explanation?

New Jersey Semiconductor

While a diode could technically accomplish the same function, using a matched transistor should give a more similar response. Dtasheet that was the case pun intendedwith your circuit, when any coil is energized they would all energize Upgrade uw browserversie of -instellingen om weer datahseet 2n datasheet krijgen tot de website van Mouser.

Finally forced air cooling 2n datasheet a fan could be used in the design or attaching a heat sink to the 2n datasheet can of the 2N would greatly reduce the amount of 2n datasheet required. If the LM78L05 stops sinking current, Q1 will turn off. Note how Q2 has its 2n40333 and emitter shorted. I love that handbook you linked to Passerby! No, create an account now. I need to calculate 2n datasheet datasheet resistor value for R1.

It would act like a diode.

Leave a Reply